You are here: Home / News / Industry News / How to maintain Angle grinder?

How to maintain Angle grinder?

Views:0     Author:Site Editor     Publish Time: 2021-03-04      Origin:Site

Angle grinder is an abrasive tool used for cutting and grinding. Makute Angle grinders are suitable for deburring and polishing a variety of materials. It has many uses, and it is commonly used by woodworkers, bricklayers, and electric welders.

But its maintenance is often ignored by us. How to maintain makute electric tools?


This passage is going to talk about the following questions of maintain an angle grinder:

(1)How to maintain angle grinder?

(2)How to check your angle grinder?

(3)How often does the angle grinder need to be cleaned?

 

(1)How to maintain angle grinder?

The maintenance of Makute angle grinder should be run through frequently.

Always check whether the power cord is firmly connected, whether the plug is loose, and whether the switch action is flexible and reliable.

Check whether the brushes are too short of wear, and replace the brushes in time to prevent excessive sparks or burning of the armature due to poor contact of the brushes.

Pay attention to check that the inlet and outlet of the tool should not be blocked, and remove the oil and dust from any part of the tool.

Grease should be added in time. After the machine has been used for 50 hours, the grease needs to be replaced. The more time you spend using the machine, the more you need to pay attention to grease.

Angle grinder 

(2)How to check your angle grinder?

If the tool fails, send it to the manufacturer or the designated maintenance center for repair. If the tool is damaged due to abnormal use or man-made wrong disassembly and repair, the manufacturer generally does not repair or exchange it free of charge.

Check the markings of makute angle grinder. Angle grinders that cannot be used include: unmarked, unclear markings, unverifiable, regardless of defects.


Check the disadvantages of angle grinders. Visual inspection, directly observe whether there are cracks and other problems on the surface of the angle grinder with eyes. Then click to check. If there is no problem with the angle grinder, it should be a crisp sound, if it is other sound, it should be a problem.

Check the rotation strength of the angle grinder. The same type of angle grinders of the same batch of models are used for random inspection of rotation strength. Angle grinders that have not been tested can never be installed and used.

Check carbon brushes and gearbox. After prolonged use, carbon brushes are most likely to wear. Check this, if their length is less than 5mm, please replace them.

 

(3)How often does the angle grinder need to be cleaned?

As a frequently used machine, one of the main ways to keep the machine running is to clean it frequently. Although many people believe that regular cleaning is best, weekly cleaning is the best. After using the angle grinder, make sure to clean it. You should always keep the equipment clean. After each use of the grinder, disconnect the power and brush or wipe off the dust and sludge (if the grinding is wet or using the built-in spray system). Tilt the grinder back, remove the tool and wipe the head. Inspect the board and guard to ensure that the screws and bolts are in place and tightened.

 

You may ask why is makute angle grinder maintenance important? In order to avoid tipping or grinding off the makute angle grinder due to basic or timely failures, it must be maintained. Maintenance is one of the key factors to make full use of angle grinders. Remember, makute angle grinders are very simple and you can do many things if you maintain them properly.


In short, makute angle grinders need to be properly maintained so that they can operate normally. Preventive maintenance will greatly change the way the tool works. Follow the steps above to optimize and maintain tool performance to the greatest extent.




Tel: 0086-579-87566667
Fax: 0086-579-87566687
Andy: 0086 13858902892(WhatsApp/We chat) 
 


No.68,Tengfei Road, Xiangzhu Idustrial Area, Yongkang City, Zhejiang Province

 

Quick Link

YONGKANG XIAOCHENG ELECTRIC APPLIANCE CO., LTD.     One of the professional power tools manufacturers  , which located in Yongkang, the hardware center of China. We have more than 10 years’ experience in R&D, and our major products are angle grinder, electric drill, impact drill, electric blower, trimmer and hammer drill. READ MORE>>

SEND US A MESSAGE
 Copyrights 2019 MAKUTE All rights reserved. Technology by www.leadong.comSitemap