You are here: Home / News / Industry News / How to avoid drilling into electrical wires?

How to avoid drilling into electrical wires?

Views:0     Author:Site Editor     Publish Time: 2021-01-20      Origin:Site

When doing home appliance renovations, holes may be punched into the wires. This is very dangerous and it is troublesome to repair broken wires. So how to avoid drilling into electrical wires when using Makute electric drill?


This passage is going to talk about the following situations of drilling into electrical wires:

(1)If there are no sockets or switches on the wall or not

(2)If there are cracks on the wall tiles or not

(3)Are the holes in the walls along the ground?

(4)Do you want to work on the suspended ceiling?

(5)Do not make holes in the horizontal and vertical directions of the switch socket

(6)Do not punch holes around the distribution box and under the door frame

(7)View decoration files before decorating

 

(1)If there are no sockets or switches on the wall or not

Before use Makute electric drill, observe carefully. If one side of the wall is white without any switches or sockets, there are generally no pipes in the white wall, so you can drill safely.

electric drill

(2)If there are cracks on the wall tiles or not

After installing the pipe on the wall, it must be grooved first. After the pipe is buried, cement will be put in the groove, resulting in the new and old walls. Many new and old walls will appear a thin, long crack after a few years of renovation. There is probably a pipe under the crack. Of course, it does not have to be combined with other phenomena.

 

(3)Are the holes in the walls along the ground?

The walls along the ground generally have pipes. Wire pipes and network cable pipes generally run along the corners of the ground, so it is best not to punch holes in the walls close to the ground, otherwise the pipe may be penetrated.

 

(4)Do you want to work on the suspended ceiling?

The pipes in the kitchen and bathroom either go from the ground or from the top. If you walk from the ground, there is a pipe in the wall that is perpendicular to the faucet; if you walk from the top, there is a pipe on the upper part of the faucet, and you can see the direction of the water pipe by disassembling the ceiling.

 

(5)Do not make holes in the horizontal and vertical directions of the switch socket:

When installing water and electricity, strict construction will follow the standard of "horizontal and vertical", so there may be sockets and switches on the wall. When drilling holes, avoid places that are horizontal or vertical.

 

(6)Do not punch holes around the distribution box and under the door frame:

The power distribution box has the largest number of wires and lines, and they are crisscrosses. For safety, it is recommended to avoid holes when drilling to avoid accidents. Under the door, frame is often the junction of wires. It is recommended not to punch holes. At the border intersection of the corridor, there are usually many pipes to avoid.

 

(7)View decoration files before decorating:

When decorating, it is best to establish decorating files, lay out the water and electricity. Take a few more photos from multiple angles, so that you can view them when you need to punch holes in the future and directly avoid punching the power cord when punching. Keep the wiring diagram of the wire so that you can easily check whether the punch position is safe.

 

After the decoration, the room looks beautiful but there are various pipes hidden inside, such as water pipes, electrical wiring pipes, network cable pipes, and sewer pipes. If you want to use Makute electric drill to drill a hole or make a nail in the wall at this time, then you have to be careful. If you are not careful enough, you may drill into the pipe or wire. Observe carefully and construct carefully!


Makute power tools will provide you with the best service. If you have any needs, please contact us.




Tel: 0086-579-87566667
Fax: 0086-579-87566687
Andy: 0086 13858902892(WhatsApp/We chat) 
 


sales5@makute.com
export@makute.com
  ivan@makute.com
 


No.68,Tengfei Road, Xiangzhu Idustrial Area, Yongkang City, Zhejiang Province

 

Quick Link

YONGKANG XIAOCHENG ELECTRIC APPLIANCE CO., LTD.     One of the professional power tools manufacturers  , which located in Yongkang, the hardware center of China. We have more than 10 years’ experience in R&D, and our major products are angle grinder, electric drill, impact drill, electric blower, trimmer and hammer drill. READ MORE>>

SEND US A MESSAGE
 Copyrights 2019 MAKUTE All rights reserved. Technology by www.leadong.comSitemap